The stately grandeur of a grandfather clock can create an atmosphere or charm or one of coziness. There are so many iconic cultural images in movies, books and television shows that feature grandfather clocks. This heirloom piece can last for centuries with the right care and upkeep.

How to Replace a Battery-operated Quartz Movement

Despite the need for regular maintenance, you can perform a lot of it yourself with the right materials and steps. Dust the grandfather clock every week. Use an ostrich feather duster because it doesn't weight much or put pressure on delicate parts of the clock. Dust the front of the clock. Then open the panel and gently dust the inside. Clean the glass on the grandfather clock weekly. Use a non-ammonia glass cleaner and a soft lint-free cloth. Spray the cleaner directly on the cloth, then wipe down the glass outside the clock.

Open both the large door that covers the pendulum and the small door that covers the clock face. Wipe down the inside. Wax and polish the wood of the grandfather clock about every two to three months. Apply the furniture polish to a soft cloth. Then rub the polish into the wood. Avoid the glass surfaces and don't ever polish the clock face.

Call a professional to clean the inside of the clock every six to eight years. Oil and dust buildup will happen within the gears and mechanisms inside the grandfather clock. It requires a professional to disassemble the inner workings, clean them and put them back together. If you attempt to clean the mechanisms of your grandfather clock yourself, you will void the warranty and risk breaking the clock.

Oil the grandfather clock every two years or whenever it seems to be slowing down. Oil kits can be purchased from furniture stores that sell grandfather clocks or upscale clock stores. Inside the kit are small bottles of oil and application tools to do the job. To oil the clock, take off the clock movement or dial to reach the front plate. Gently put oil on each intersection of the clock plate and the gears.The most important aspect of owning a grandfather clock is to take care of the grandfather clock movements.

how to remove howard miller grandfather clock movement

Generally, due to the different types of clocks available, finding the cause of the problem can be confusing. The rules are completely different for grandfather clocks that are more than 50 years old.

They are classified as antiques. In case you do not feel fully confident to do this job on your own, you can always consult a professional. The tips below can help you fix the faulty movement of your grandfather clock. Weights control the grandfather clock movements. A weight provides the power required for the time and chime of the clock to function. Examine and see if the weights are aligned properly.

If they are misaligned, set them right by referring to the marks at the bottom. These marks indicated the exact alignment for the weights. Place the weights on the correct side, since only then will the grandfather clock movements be accurate. If the pendulum does not swing, it will lead the hands on the grandfather clock to freeze. The hands have to be unlocked.

Pull the weights up, open the glass and gently move the hands away from each other.

Mechanical Clock Movement Identification

Be careful while doing this, as the hands are quite delicate. Sometimes the pendulum can disrupt the grandfather clock movements. If the clock is running slow move the pendulum up the shaft, and if it is running fast move it down.

Another cause for the inconsistency could be the moon dial. Observe the current phase that the moon is in. Now reset the moon dial with the observed moon phase. You can rotate the moon by gently pressing the dial. Check the platform where the grandfather clock has been stationed.

Grandfather Clocks Movements – Replace or Repair

If the platform is not in a level eventually it will affect the grandfather clock movements. Adjust the leveling of the platform. Test this by observing the swing of the pendulum. If the swing is correct this problem will not resurface. If you are unable to find a leveled surface, then listen carefully to the ticking.Cecilia Harsch has been writing professionally since She writes mainly home improvement, health and travel articles for various online publications.

She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction.

Harsch received her Certified Nurses Assistant license in She attended Tarrant County College and studied English composition. Each of the weights on your grandfather clock has a different job and drops at a different speed depending on that job.

The weight on the right operates your clock's chimes, the center weight moves the pendulum and the clock hands and the weight on the left side of your clock powers the hour strike. When making repairs, you may need to dismantle your clock, and that could require lowering the weights down to the grandfather clock floor.

Open the front door on your grandfather clock to access the pendulum. Stop the pendulum movement with your hand.

how to remove howard miller grandfather clock movement

Grasp the pendulum with your hand. Lift up on the pendulum to unhook it from the pendulum guide attached to the clockworks. Carefully lay the pendulum aside. Remove the side access panels from the grandfather clock cabinet. Locate these panels on both sides of the clock and designed to allow access to the clockworks.

Depending on the manufacturer and design of your clock, the panels are made of wood or glass. Slide the panels up to release them from the grooves cut in the clock cabinet, and pull them from the cabinet.

Reach inside the clockworks. Find the winding barrels behind the face of the clock that hold the weight cables. Lift the level that engages the teeth on the barrel while holding the weight. This releases the weight and allows you to lower the weight inside the clock. Pin Share Tweet Share Email. Lower the weights correctly on your grandfather clock. Step 1. Step 2. Step 3.A Howard Miller clock has various mechanisms within the clock that may need to be repaired if the clock is an antique, or the clock may just need an adjustment in general.

Sometimes the clock mechanisms become damaged upon moving the clock, or there may need to be an adjustment made on a faulty piece. Some antique Howard Miller clocks need to be oiled. Both antique and contemporary clocks need to be oiled once every three years as oiling keeps the mechanisms inside the clock running smoothly.

Repair the moon dial if it is not working correctly. Face the clock and remove the top side panel. Open the door on the side or remove the panel from the back access section.

Look inside at the back side of the dial to locate the click spring. Place your pointer finger on the tip of the click spring. Watch to see if the click spring and saw tooth moon dial snap into alignment. Rotate the minute hand backward 3 hours. The minute hand is the smaller hand that tells time on the clock face.

Fix the clock chime if it is not chiming at the correct time. Stop the pendulum and record the time. Use small pliers to remove the small nut that holds the minute hand. Carefully turn the nut counterclockwise with the pliers while holding the minute hand with your other fingers. Remove the minute hand by grasping the point that is attached to the shaft and pull the hand forward and off.

Turn the clock dial forward or backward to chime at the correct time. Reattach the minute hand and tighten the small nut without over-tightening to secure the minute hand back in place.

Start the pendulum by pushing it either left or right. Reset the time. Move just the minute hand backward. Move the hour hand forward to fix the time the clock strikes hourly if it is not striking on the correct hour.

Move the minute hand again only to reset the time, and then move that hand backward. Check to see if the lever on the clock is halfway between two chime melodies if the clock fails to chime or strike. Check to see that the clock is not in the nighttime silence mode if it fails to chime. Position weights correctly. Look at the bottom of the weights where they are labeled with their directions: left, right or center.

Replacing A Howard Miller Wall Clock Movement

Realign the weights if they are tangled to reset them in their proper places. Linda Stamberger began writing professionally inas an entertainment reporter for "Good Times Magazine. By: Linda Stamberger Updated April 12, Share It. About the Author. Photo Credits.Was this helpful?

Need a Part? Browse the "Order Parts for Clocks and Cabinets" section below. Toggle navigation.

how to remove howard miller grandfather clock movement

Tags movement 4 replacement 5. Share this Facebook Twitter LinkedIn. Share this. Battery-operated, quartz dual chime movement will not operate. Broken or damaged chime rods.

Can I adjust the chime volume of my mechanical clock? Can I get the purchase or registration history of my clock? Can the volume of the ticking or "tic toc" sound be changed? Chimes or strike of a weight-driven clock seem fast or slow. Dial hands are bent. How do I install and use a part I purchased from the Parts Store? How do I remove the shield from the tubular light assembly? How do I replace the bulb in my tubular light assembly? How do I return a clock that I purchased.

How do radio controlled clocks work? How to adjust a floor clock for Daylight Savings Time How to adjust the chimes to play precisely on the proper time.

How to adjust the chime tone. How to adjust the time speed of a floor clock. How to change the time on a quartz, battery-operated movement. How to clean and maintain a clock. How to clean the inside glass of a floor clock case.How do I prolong the life of my Grandfather clock? Usual care for grandfather clocks is to have the clock oiled about every five years.

Oiling the clock takes expertise by removing the hands and dial so the front of the movement can be accessed to apply the special types of oils used to reduce the friction in your grandfather clock. What should I do if I need to move my grandfather clock? Get a professional or clock technician to at least pack the grandfather clock for you prior to moving.

When a grandfather clock is packed properly, you may move it like any other piece of furniture. If the chains come off the sprockets or the cables tangle and cross, the grandfather clock will not run when you get it to your new home. The cost of having someone pack it for you will most probably outweigh the cost of repair of the grandfather clock.

How do I clean my grandfather clock? Clean the case of your grandfather clock by using a slightly damp not wet soft cloth and light cover the surfaces with the grain of the wood. Do not use a silicone based polish as this may make the silicone in the polish break down the lacquer and you may not be able to refinish or touch up the finish later. If you must use a polish, use Old English or Guardsman products that do not contain any silicones. To clean the glass on your grandfather clock, use a clean paper towel and spray your glass cleaner on the towel, not on the glass…then wipe the glass free of dust and fingerprints.

You may use a vacuum cleaner to clean the inside bottom of your grandfather clock, but do not use a blower attachment as this might blow dust and debris into the grandfather clock movement. If you need to clean behind the grandfather clock, slowly move the base away one corner at a time and do not let the pendulum or the weights to swing wildly as this may damage the timekeeping of the clock by twisting the suspension spring on the pendulum and the weights may get dented.

How do I set the time properly on my grandfather clock? For a complete primer on how to change the time, please click: how to change the time on a grandfather clock. I need grandfather clock service and do not know anyone in my area. If you are considering a new grandfather clocks, please browse our offers of new grandfather clocks at The Clock Depot with free delivery anywhere within the cont. For a complete primer on how to change the time, please click: how to change the time on a grandfather clock I need grandfather clock service and do not know anyone in my area.Care should be taken whenever you move your clock to ensure that all accessory parts such as pendulum, weights, etc.

Use cotton gloves or a soft cloth when handling the pendulum or weights. It's always recommended to contact and hire a professional furniture moving company for proper service. Local moving companies may be found online. Was this helpful? Need a Part? Browse the "Order Parts for Clocks and Cabinets" section below. Toggle navigation. How to prepare a floor clock to be moved. The foam blocks are intended to retain tension on the cables once the weights are removed. Be sure you wind the weights all the way up.

When done properly, the wire or string should go through six chain links. Secure the wire or string to prevent the chains from coming loose from the sprocket.

Carefully stop the pendulum from swinging. Remove the weights. NEVER wind the clock without the weights installed. For clocks with chains, secure the chains so that they do not damage the finish. Remove the pendulum For tubular movements, remove the tubes Keep the clock in an upright position while carefully moving it to its new location.

Set the clock up per the original set-up instructions. Ensure that the pulleys are properly located on the cables and the chains are properly located on the sprockets. Tags clocks 35 how to 9 move a clock 1. Share this Facebook Twitter LinkedIn. Share this. Battery-operated, quartz dual chime movement will not operate. Broken or damaged chime rods. Can I adjust the chime volume of my mechanical clock?

Can I get the purchase or registration history of my clock?